This is the latest recevied telemetry packets stored in our database for station/object LW2DHT-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | TX* | RX* | Digi* | V_Bat* | V_Ext* |
|---|---|---|---|---|---|
| 1781988220 | 975 Count | 915 Count | 715 Count | 0 VDC | 0 VDC |
| 1781966614 | 921 Count | 867 Count | 677 Count | 0 VDC | 0 VDC |
| 1781964811 | 916 Count | 862 Count | 673 Count | 0 VDC | 0 VDC |
| 1781963009 | 912 Count | 858 Count | 670 Count | 0 VDC | 0 VDC |
| 1781959402 | 902 Count | 849 Count | 662 Count | 0 VDC | 0 VDC |
| 1781957599 | 897 Count | 844 Count | 658 Count | 0 VDC | 0 VDC |
| 1781950420 | 873 Count | 824 Count | 642 Count | 0 VDC | 0 VDC |
| 1781946814 | 864 Count | 816 Count | 635 Count | 0 VDC | 0 VDC |
| 1781941405 | 852 Count | 804 Count | 626 Count | 0 VDC | 0 VDC |
| 1781939602 | 848 Count | 800 Count | 623 Count | 0 VDC | 0 VDC |
| 1781937799 | 844 Count | 796 Count | 620 Count | 0 VDC | 0 VDC |
| 1781934227 | 832 Count | 789 Count | 614 Count | 0 VDC | 0 VDC |
| 1781928818 | 819 Count | 778 Count | 604 Count | 0 VDC | 0 VDC |
| 1781927015 | 814 Count | 773 Count | 600 Count | 0 VDC | 0 VDC |
| 1781919803 | 796 Count | 756 Count | 586 Count | 0 VDC | 0 VDC |
*Used Equation Coefficients:
TX: 0, 1, 0
RX: 0, 1, 0
Digi: 0, 1, 0
V_Bat: 0, 0.01, 0
V_Ext: 0, 0.02, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)