DL3MC APRS Map

☰

reset

HS4IOO Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS4IOO. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TEMP*	BAR*	BAT*
1778071780	1.1 °C	800 hPa	4.18 V
1778069980	1.09 °C	800 hPa	4.13 V
1778069380	1.1 °C	800 hPa	4.18 V
1778066380	1.1 °C	800 hPa	4.18 V
1778065780	1.1 °C	800 hPa	4.11 V
1778065180	1.1 °C	800 hPa	4.13 V
1778064580	1.11 °C	800 hPa	4.19 V
1778063980	1.11 °C	800 hPa	4.18 V
1778063380	1.11 °C	800 hPa	4.19 V
1778062780	1.11 °C	800 hPa	4.19 V
1778062180	1.11 °C	800 hPa	4.18 V
1778061580	1.1 °C	800 hPa	4.1 V
1778060980	1.1 °C	800 hPa	4.13 V
1778060380	1.1 °C	800 hPa	4.19 V
1778059780	1.09 °C	800 hPa	4.18 V
1778059180	1.09 °C	800 hPa	4.19 V
1778058580	1.08 °C	800 hPa	4.18 V
1778057982	1.08 °C	800 hPa	4.18 V
1778057380	1.07 °C	800 hPa	4.1 V
1778056780	1.07 °C	800 hPa	4.13 V
1778056180	1.05 °C	800 hPa	4.19 V
1778051979	0 °C	800 hPa	4.18 V
1778051969	0 °C	800 hPa	4.18 V
1778051712	25 °C	800 hPa	4.18 V
1778050509	25 °C	800 hPa	4.19 V

*Used Equation Coefficients:

TEMP: 0, 0.01, 0

HUM: 0, 0.1, 0

BAR: 0, 0.1, 800

BAT: 0, 0.01, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Maintained by DL3MC, based on APRS Track Direct